Home / RV & camper / Antifreeze method
RV & camper
How do I winterize my RV with antifreeze?
For a typical travel trailer or motorhome with a tank water heater, the “wet” method is: turn the heater off and let it cool, drain the fresh, gray, and black systems, drain and bypass the water heater, then use the water pump (or a winterizing inlet) to pull non-toxic RV antifreeze through every hot and cold faucet, shower, outdoor shower, and toilet until the flow runs pink. Pour a little antifreeze into each drain to protect the traps. Never use automotive antifreeze. Your owner’s manual wins if it differs; tankless water heaters follow a different bypass rule.
What you’ll need
- Non-toxic RV water-system antifreeze — Winnebago’s published guide starts with two gallons and tells you to check the manual; some rigs need more (see how much to buy)
- A socket or wrench for the water heater drain plug or anode rod
- A winterizing suction kit if your RV does not already have a factory siphon hose on the pump
- Access to bypass valves (layout is in your manual) and to every fixture, including outdoor showers
- Containers for the water you drain and a way to dump tanks legally
Steps
These steps follow Winnebago’s published wet-method guidance (written around a Class A Vista, with a reminder that details differ by model). Always read your owner’s manual before you start. Winnebago manuals are available from the manufacturer.
- Turn the water heater off and let it cool completely before you open the tank. Winnebago recommends doing this the night before so you are not scalded when the drain plug comes out.
- Empty the tanks. Winnebago’s writers empty and clean the black tank first, then drain the gray and freshwater tanks. When you drain the fresh tank, also open the low-point drains so more water leaves the lines — then close those low-point drains before you introduce antifreeze, or the pink fluid will run straight out.
- Relieve pressure and drain the water heater tank. With city water disconnected and the pump off, open the water heater’s pressure-relief valve, then remove the drain plug. Some plugs are plastic; some are metal anode rods — Winnebago notes this is a good time to inspect an anode. Let the tank empty, then close the relief valve. Leave the heater on bypass later so you do not refill this tank with antifreeze.
- Set the water heater to bypass. Valve locations vary: in a cabinet, under a sink, or under a floor panel. You may have one bypass valve or a three-valve setup (inlet and outlet closed, bypass open). Your manual shows the direction of travel. This step is for conventional tank heaters. If you have a tankless unit, stop and use the tankless guide — Girard’s official manual says a bypass kit is not required and is not recommended.
- Hook the pump to the antifreeze jug. Many late-model Winnebagos have a factory clear siphon tube at the pump: uncap it, put the end in the jug, and turn the winterize valve to the winterize or open position. If you do not have that tube, a winterizing kit attaches to the pump inlet so the pump draws from the jug instead of the fresh tank.
- Pump antifreeze through every fixture. Turn the water pump on. Open each hot faucet until the stream is clearly pink, then the cold. Repeat at the shower, kitchen, any other bath, the toilet (flush until pink appears), and the outdoor shower or wash port — an easy one to miss, as Winnebago notes. Watch the jug and switch bottles when the first one runs low.
- Protect the drains. After the faucets, pour antifreeze into each sink, shower, and related drain so the P-traps are protected. A Travato operator’s manual specifies about one cup down the galley and lavatory drains; use your manual if it gives a volume.
- Service add-ons separately. Winnebago’s guide: unscrew a whole-house filter canister, remove the cartridge, and reinstall the empty canister. Ice makers and washing machines have their own winterizing steps — consult those appliance manuals rather than assuming a generic procedure. Do not skip a city-water inlet or black-tank flush line if your manual has a step for them (for example, the Travato manual has you open the city-fill inlet and press the backflow valve to clear trapped water).
- Shut down. Turn the pump off, return the winterize valve to the normal position, cap the siphon tube, and reinstall the water heater drain plug as your guide describes. The rig should not be used for drinking water until you flush and sanitize in the spring.
Common mistakes and variations
Leaving water in low points or the city-fill check valve
If low-point drains stay open, you will pump antifreeze onto the ground. If you close everything but never clear the city-water inlet, that short run can still hold water. Use the inlet/backflow step in your manual.
Filling the water heater tank with antifreeze by accident
A typical RV tank heater holds several gallons. The point of the bypass, in Winnebago’s supplies article, is to avoid buying extra antifreeze just to fill the heater. Confirm valve position before you start the pump.
Full-time winter living is a different job
Storage winterizing (filling lines with antifreeze or blowing them dry) is not how you keep a trailer livable in the cold. If you will occupy the RV, follow a winter-use or four-season procedure from the manufacturer — and do not pump antifreeze into a system you still need for drinking water.
FAQ
Can I use automotive antifreeze?
No. Winnebago’s winterizing articles warn you not to use automotive antifreeze or coolant in the RV water system. Automotive products often contain ethylene glycol, which can cause blindness or death if ingested. Use a non-toxic RV water-system antifreeze (commonly propylene glycol, sold as pink RV antifreeze) approved for potable plumbing. It is still not a beverage — Winnebago’s writers note you should not drink it.
How much antifreeze will I need?
A Winnebago winterizing guide starts with two gallons and says to check your manual because some RVs need a bit more. A 2019 Winnebago Travato operator’s manual has you place the siphon tube in a container with 2 to 3 gallons for the line-fill procedure, then pour about a cup down each sink drain. See our quantity guide for what changes the total.
Do I put antifreeze in the water heater tank?
Not if you can bypass and drain it. Winnebago’s wet-method guide has you drain the tank and set the bypass so antifreeze does not enter the heater, which avoids filling a large tank with several extra gallons. Bypass valve layouts differ (one valve or up to three). This advice is for typical tank heaters, not every tankless unit — see the tankless guide.
What if I also blow the lines out with air?
Winnebago describes a dry method that uses regulated compressed air and a blow-out plug, plus some antifreeze in P-traps, the toilet, and sometimes a washer. A Travato operator’s manual includes both a blow-out procedure (air regulated to 30 psi or less at the city-fill inlet) and an antifreeze fill. Follow the sequence in your own manual.
Sources
We checked these pages and documents while writing this guide. Follow your own manual if it differs.
- RV Winterizing Guide: Helpful Tips & Special Considerations — WinnebagoSeptember 2021 Winnebago Life article by Kenny and Sabrina Phillips. Wet-method steps, two-gallon starting quantity, cooling the heater, bypass, fixtures, and the warning to check your manual.
- Winterizing Your RV — WinnebagoWinnebago Life overview with the warning never to use automotive antifreeze in RV plumbing.
- Basic Supplies for RV Winterization — WinnebagoExplains why a water-heater bypass avoids filling the tank with extra antifreeze.
- 2019 Winnebago Travato Operator’s Manual (plumbing / winterizing section, via ManualsLib)Official-procedure excerpt: 2–3 gallons of non-toxic RV antifreeze for the siphon fill, blow-out air at 30 psi or less, about a cup of antifreeze down each sink drain, and the ethylene-glycol warning. Always prefer a copy from Winnebago if you have one.